Multi-size (1"to 7" diameter) pre-molded EPDM boot used to flash pipes. Use only when outside corner wall or curbsĪre square. Use only when inside walls or curbs are sĪ cured, premolded white EPDM outside corner for use in Re-Flex EPDMįully Adhered Installations. Available in 6" x 100' rolls.Ī cured, premolded white EPDM inside corner for use in Re-Flex EPDMįully Adhered installations. Used to flash in metal drip edge and other single plane (angle) flashings. Use RPI Scrub Pad and Re-Flex Seam Tape Primer/Activator in application.Ĭured EPDM membrane laminated to Seam Tape. Available in 6" and 12" widths, and 25' and 50' lengths. Moldable uncured EPDM membrane with tape backing used for flashing details, protrusions, T-Patches, and field seams incorporating angle changes. NOTE: Re-Flex Seam Tape Primer/Activator must be used before applying Re-Flex Seam Tape. Available in 3", 4", and 7" x 100' rolls. Color: WhiteĪ butyl tape used to create a seam by adhering one membrane to another in lieu of using Splice Adhesive. Used in Re-Flex EPDM and Re-Flex TPO Systems. Used to apply Seam Tape Primer/Activator. Which may be required is different states.Ī porous scrub pad laminated to a plastic handle. Royal Edge Low VOC Membrane Cleaner is formulated to meet low VOC restrictions Used in Royal Edge EPDM, Re-Flex EPDM, and Re-Flex TPO SystemsĪ specially formulated cleaning agent used to clean talc and other contaminants fromĮPDM and metal flashings prior to applying Splice Adhesives or Primers. Meets OTC (Ozone Transport Commission) VOC emission restriction requirements. Used in Royal Edge EPDM, Re-Flex EPDM, and Re-Flex TPO Systems. Re-Flex Low VOC MEMBRANE CLEANER Color: Clear Also used to clean Metal Drip Edge prior to installing Cover Strip or Cover Tape. Used to clean EPDM surfaces before seaming with Splice Adhesive or Seam Tape. Solvent-based primer applied to clean membrane prior to installing Re-Flex Seam Tape or Tape Backed Cured or Uncured membrane. Adhesive is applied to both surfaces and allowed to "flash-off" (dry), before mating surfaces together per gallon.Ĭoverage may increase/decrease depending on the porosity of the substrate. Solvent-based adhesive is available in 5 gallon pails. Check with manufacturer for compatibility of material with adhesive. Color: Amber/GoldĪ low VOC solvent adhesive used to adhere EPDM/TPO membrane to insulations, plywood, OSB, concrete, and block or brick. Used in Royal Edge EPDM, Re-Flex TPO, and Re-Flex EPDM Systems. (solvent based low voc contact adhesive)* per gallon depending on pouracity of substrate. Adhesive is white when wet, and turns clear when dry. May be installed "wet", (single surface), or "dry", (applied to both surfaces and allowed to "flash-off" (dry). Used to adhere EPDM membrane to insulations, plywood, OSB, concrete and other low slope surfaces. Color: WhiteĮnviromentally friendly water based adhesive. Used in Royal Edge EPDM and Re-Flex EPDM Systems. ROYAL EDGE BONDING ADHESIVE: (Water-Based) Adhesive is applied to both surfaces and allowed to "flash-off" (dry), before mating surfaces together. Solvent-based adhesive comes in 1 or 5 gallon pails. Used to adhere EPDM membrane to insulations, plywood, OSB, concrete, and block or brick. ROYAL EDGE BONDING ADHESIVE (solvent based contact adhesive) (white on black), cured single-ply membrane used in RPI Re-Flex EPDM Fully Adhered RPI Re-Flex EPDM is a highly reflective, non-reinforced. RE-FLEX EPDM Products RE-FLEX EPDM MEMBRANE Color: White
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |